- 您现在的位置：买卖IC网 > Sheet目录395 > AS3932-BTST (ams)IC RF PROGRAM 16-TSSOP
AS3932
Datasheet - D e t a i l e d D e s c r i p t i o n
8.3.2
Antenna Damper
The antenna damper allows the chip to deal with higher field strength, it is enabled by register R1<4> . It consists of shunt resistors which
degrade the quality factor of the resonator by reducing the signal at the input of the amplifier. In this way the resonator sees a smaller parallel
resistance (in the band of interest) which degrades its quality factor in order to increase the linear range of the channel amplifier (the amplifier
doesn't saturate in presence of bigger signals). Table 16 shows the bit setup.
Table 16. Antenna Damper Bit Setup
R4<5>
0
0
1
1
R4<4>
0
1
0
1
Shunt resistor (parallel to the resonator at 125 kHz)
1 k Ω
3 k Ω
9 k Ω
27 k Ω
8.4 Channel Selector / Demodulator / Data Slicer
When at least one of three gain channel enters initial wake-up state the channel selector makes a decision which gain channel to connect to the
envelope detector. If only one channel is in wake-up state the selection is obvious. If more than one channel enters wake-up state in 256μs
following the first active channel the channel with highest RSSI value is selected. The output signal (amplified LF carrier) of selected channel is
connected to the input of the demodulator.
The performance of the demodulator can be optimized according to bit rate and preamble length as described in Table 17 and Table 18 .
Table 17. Bit Setup for the Envelop Detector for Different Symbol Rates
R3<2>
0
0
0
0
1
1
1
1
R3<1>
0
0
1
1
0
0
1
1
R3<0>
0
1
0
1
0
1
0
1
Symbol rate [Manchester symbols/s]
4096
2184
1490
1130
910
762
655
512
If the bit rate gets higher the time constant in the envelop detector must be set to a smaller value. This means that higher noise is injected
because of the wider band. The next table is a rough indication of how the envelop detector looks like for different bit rates. By using proper data
slicer settings it is possible to improve the noise immunity paying the penalty of a longer preamble. In fact if the data slicer has a bigger time
constant it is possible to reject more noise, but every time a transmission occurs, the data slicer need time to settle. This settling time will
influence the length of the preamble. Table 18 gives a correlation between data slicer setup and minimum required preamble length.
Table 18. Bit Setup for the Data Slicer for Different Preamble Length
R3<5>
0
0
0
0
1
1
1
1
R3<4>
0
0
1
1
0
0
1
1
R3<3>
0
1
0
1
0
1
0
1
Minimum preamble length [ms]
0.8
1.15
1.55
1.9
2.3
2.65
3
3.5
www.ams.com/LF-Receiver/AS3932
Revision 1.7
21 - 34
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
AS500106
TLAPS MAGNET CARRIER
AS5263-HQFT-500
IC ENCODER ROTARY 12BIT 32-QFN
AT 150 B420L
SENSOR CURRENT 150A 30V MOD
AT 150 B5
SENSOR CURRENT 150A MOD
AT 20 B10
SENSOR CURRENT 20A MOD
AT-7666A
SENSOR AMORPHOUS 146X167.5X0.3
AT094
PCB ADAPTER FOR DSA01
AT86RF212-ZUR
TXRX AVR LOW PWR/VOLTAGE 32PQFN
相关代理商/技术参数
AS3932-DB
制造商:ams 功能描述:AS3932 Demo Board Rx & Tx
AS3932-DK
制造商:ams 功能描述:AS3932 Development System
AS3933 DB
制造商:AMS 功能描述:BOARD DEMO FOR AS3933
AS3933 DEV SYSTEM
功能描述:BOARD DEMO FOR AS3933 制造商:ams 系列:- 零件状态:有效 类型:接收器，ASK 频率:125kHz 配套使用产品/相关产品:AS3933 所含物品:2 板，电源，软件 标准包装:1
AS3933BQFT
制造商:ams 功能描述:T&R / QFN 16 (4x4)
AS3933-BQFT
功能描述:射频接收器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
AS3933-BQFT-CUT TAPE
制造商:AMS 功能描述:AS3933 Series 3.6 V 150 KHz 3D Low Frequency Wakeup Receiver - QFN-16
AS3933BTST
制造商:ams 功能描述:T&R / TSSOP 16